PhantomX Reactor Robot V2 - Revision history

Aguti at 18:12, 11 June 2026

2026-06-11T18:12:42Z

Aguti at 18:12, 11 June 2026

2026-06-11T18:12:28Z

Aguti at 18:12, 11 June 2026

2026-06-11T18:12:09Z

Aguti at 18:11, 11 June 2026

2026-06-11T18:11:52Z

Aguti at 18:09, 11 June 2026

2026-06-11T18:09:12Z

Aguti at 18:08, 11 June 2026

2026-06-11T18:08:36Z

Aguti at 18:04, 11 June 2026

2026-06-11T18:04:07Z

Aguti at 18:01, 11 June 2026

2026-06-11T18:01:20Z

Aguti: Created page with "TOC Note: Most of the information of this website is obtained from: https://emanual.robotis.com/docs/en/parts/controller/openrb-150/#install-the-arduino-ide Ple..."

2026-06-05T08:16:43Z

Created page with "__TOC__ Note: Most of the information of this website is obtained from: https://emanual.robotis.com/docs/en/parts/controller/openrb-150/#install-the-arduino-ide Ple..."

New page

__TOC__

 Note: Most of the information of this website is obtained from:
https://emanual.robotis.com/docs/en/parts/controller/openrb-150/#install-the-arduino-ide
Please refer to the previuos link if you need more information.

<h1> Configuring the environment </h1>

<h2> Setting up the Arduino Software </h2>

<ul>
<li> Download the Arduino IDE according to your operating system from: https://www.arduino.cc/en/Main/Software . </li>
<li> Install the Arduino IDE </li>
<ul>
<li> If you have chosen to download the installer, run the installer and install the software in a path of your convenience. </li>
<li> If you have chosen to download the sources (Linux or zip on Windows), uncompress the software in a path of your convenience </li>
</ul>
<li> Open/run Arduino IDE, so it will create all the folders needed</li>
<li> Close Arduino IDE </li>
</ul>

<h2> Installing Tools and Libraries </h2>
<ul>
<li> Download the robot libraries from: [[https://www.robolabo.etsit.upm.es/wikiFiles/Arbotix-arduino-1-6.zip here ]]. </li>
<li> Uncompress the libraries to a path of your convenience. In this file you will find two folders: hardware and libraries 
<li> Copy both folders to the <ARDUINO_MAIN_DIRECTORY>. In some Windows you will find this folder in My Documents\Arduino\ , while in others you will find it in Documents\Arduino\ .
In Linux you will find this folder in ~/Arduino/. 

 Important: If you already have a libraries folder inside your <ARDUINO_MAIN_DIRECTORY>, move the content of the libraries folder downloaded inside the libraries folder of <ARDUINO_MAIN_DIRECTORY>.
</ul>

<h2> Check installation </h2>
<ul>
<li> Open/run Arduino IDE </li>
<li> Open a Robot Test: </li>
<pre>
File -> Examples -->ArbotiX --> Tests --> ReactorTest
</pre>

<li> Select the Arbotix board </li>
<pre>
Tools -> Board -> ArbotiX Std
</pre>

<li> Compile the program </li>
<pre>
Program-> Verify/Compile
</pre>

If there is no errors, you are ready for the next step.
If you found some errors, please review the previous steps.

<li> Close Arduino IDE
</ul>

<h3> Installing FTDI drivers </h3>
If you are using Linux or Mac, skip this step.
If you are using Windows, power up the robot and connect it to your computer.
Windows should ask you to install some FTDI drivers to be able to connect to the robot.

<h1> Hello World example </h1>

We have created a helloWorld example to test the communication with the robot.
Please download it from [[https://www.robolabo.etsit.upm.es/wikiFiles/ROB-HelloWorldPhantomReactor.tgz here ]] in your prefered destination.
Untar the file:
<pre>
tar -xvzf helloWorld.tgz
</pre>

<h2> Compiling the code </h2>
<li> Open Arduino IDE and load the .ino file in your environment: </li>
<pre>
File --> Open --> <HELLOWORLD_EXAMPLE>
</pre>

<li> Select the Arbotix board: </li>
<pre>
Tools -> Board -> ArbotiX Std
</pre>

<li> Compile the program: </li>
<pre>
Program-> Verify/Compile
</pre>

<h2> Downloading the code to the robot </h2>
Once compiled, select the correct por to download the binaries:
In Linux, typically:
<pre>
tools -> Port -> /dev/ttyUSBX
</pre>

In Windows, typically:
<pre>
tools -> Port -> COMX
</pre>

where X depends on your system and the number of peripherals on it

Upload your code to the board:
<pre>
Program -> Upload
</pre>

The IDE will notify that it is uploading and after some seconds it will say uploaded .

<h2> Playing with HelloWorld </h2>

This example allows you to move different joints of the robot.

Once the code have been loaded, you can open the serial port:
<pre>
Tools --> Serial Monitor
</pre>

Important:
<ul>
<li> Select 115200 bauds. This is the speed selected on the code for communicating with the robot.
<li> Select "No line ending". To avoid sending a line end after entering commnds.
</ul>

In some seconds you should see the board communicating the following menu:
<pre>

################################
Serial Communication Established
################################
################################
Please enter option 1-6
0) Relax Servos
1) Hold Servos
2) Get Joints Pos
3) Gripper Close
4) Gripper Open
5) TestAllJoints
6) MoveSpecificJoint
################################
</pre>

These are the different options:
<ul>
<li> Option 0 unpowers the servomotors of the robot.
<li> Option 1 powers the servomotors of the robot.
<li> Option 2 prints the position of every generalized coordinate (Base, Shoulder, Elbow, Wrist and Wrist rotation).
<li> Option 3 closes the gripper.
<li> Option 4 opens the gripper.
<li> Option 5 provides a test movement for the complete robot.
<li> Option 6 allows to move specific joints. In this case, once the option is selected, the following menu will appear:
</ul>
<pre>
Base: 0
Shoulder: 1
Elbow: 2
Wrist: 3
Wrist Rot: 4

Joint to move?:
</pre>

The user must choose one of the 5 options, which correspond to different joints.

For every joint, once selected, the program will ask for a position to move, given the limits of the joint, for example:

<pre>
Joint selected: 1
Shoulder: [-0.33, 2.97]
Position to move?:
</pre>

Once the position is provided through the serial port it will return all the information inserted, for example:

<pre>
Moving Joint: 1 to position: 1.57
</pre>

and it will move to the specified position.

<h1> Practice Template </h1>

For the implementation of the Practice of the "Control and Robotics in Medicine" subject of the "Master on Bioengineering" of the UPM, we have created a students template.
You can download the template from [[https://www.robolabo.etsit.upm.es/wikiFiles/ROB-P1Template.tgz here ]]

<h2> Structure </h2>
The template has 4 different files:
<ul>
<li> poses.h : A file where different generalized coordinates can be stored.
<li> servos.h : A library to manage the servomotors independently.
<li> robot.h : A library to manage the different joints of the robot.
<li> P1-Template.h : The place where the practice should be developped.
</ul>

<h2> Libraries </h2>
This Section provides important information for the resolution of Practice1.
It is based on the explanation of different methods to control the robot, but it does not explain the complete set of methods.
To get and exahustive description of all methods the servos.h and robot.h files must be studied.

In principle, all interaction with the robot will be made by means of the robot.h library.
Main methors are as follows:

<ul>
<li> void ROBOT_GripperOpen(void) : It opens the gripper, so it can release an object if already grasped.
<li> void ROBOT_GripperClose(void) : It close the gripper, so it can grasp an object if correctly located.
<li> void ROBOT_SetSingleTrajectory ( double *f_pos, uint16_t un_time, uint8_t un_trajectory_type ) : It performs a trajectory form one point (Q(t0)) to another point (Q(tf)).
Q(t0) and Q(tf) are defined as generalized coordinates Q={q1,q2,q3,q4,q5}.
Moreover, Q(t0) is defined as the coordinates at which the robot is located once the instruction is set.

<ul>
<li> double *f_pos :
Q(tf) is coded as double * , for example:
<pre>
double m_fCoordTest[] = {0,M_PI/2,-M_PI/2,0,0};
</pre>

<li> uint16_t un_time , represents the time that it takes to travel from (Q(t0)) to Q(tf),that is: tf - t0 in milliseconds.

<li> uint8_t un_trajectory_type , represents the type of trajectory to perform: Linear (LINEAR = 0) or Cubic (CUBIC1 = 1)

 
 
Therefore, if we want to move the robot for the actual position to position m_fCoordTest taking 2 seconds with a linear function, we need to execute:

<pre>
ROBOT_SetSingleTrajectory (m_fCoordTest, 2000, LINEAR);
</pre>

I we want to move the robot to the same coordinates but in 10 secons with a cubic function, we need to execute:
<pre>
ROBOT_SetSingleTrajectory (m_fCoordTest, 10000, CUBIC1);
</pre>

</ul>
<li> void ROBOT_SetDoubleTrajectory ( double *un_pos1, double *un_pos2, uint16_t un_time1, uint16_t un_time2, uint8_t un_trajectory_type ) :
It performs a trajectory form one point (Q(t0)) to another point (Q(tf)) passing by a point (Q(tv)).

Q(t0), Q(tf) and Q(tv) are defined as generalized coordinates Q={q1,q2,q3,q4,q5}.
Moreover, Q(t0) is defined as the coordinates at which the robot is located once the instruction is set.

<ul>
<li> double *f_pos1 :
Q(tv) is coded as double * , for example:
<pre>
double m_fCoordTest[] = {0,M_PI/2,-M_PI/2,0,0};
</pre>

<li> double *f_pos2 :
Q(tf) is coded as double * .

<li> uint16_t un_time1 , represents the time that it takes to travel from (Q(t0)) to Q(tv),that is: tv - t0 in milliseconds.
<li> uint16_t un_time2 , represents the time that it takes to travel from (Q(tv)) to Q(tf),that is: tf - tv in milliseconds.

<li> uint8_t un_trajectory_type , represents the type of trajectory to perform. Only cubic trajectories are allowed (CUBIC2 = 2)

 
 
Therefore, if we want to move the robot for the actual position to position m_fCoordTest taking 5 seconds passing by m_fCoordVia with 2 seconds from the start, we need to execute:

<pre>
ROBOT_SetDoubleTrajectory (m_fCoordVia, m_fCoordTest, 2000, 3000, CUBIC2);
</pre>

</ul>
</ul>

<h2> Implementation </h2>

 P1-Template.ino follows the same structure as the helloWorld.ino example.
However, a new option has been included in the menu (Opcion A).
This option calls the P1Solution method.
If you open P1-Template.ino and go to the end of the file, you will see the following code:

<pre>
void P1Solution ( void )
{
/* START CODE TO BE IMPLEMENTED BY THE STUDENTS */

/* END CODE TO BE IMPLEMENTED BY THE STUDENTS */
}

</pre>

It is between those comments where you must implement all functions required to achive the task.
Remember you may need some delay instructions, defined as void delay (uint16_t millisec) , to prevent some instructions to execute before you need them.

 
Moreover, in the poses.h file you can find some examples of how to define the generalized coordinates of your system.

@@ Line 98: / Line 98: @@
 </pre>
-<b>VERY IMPORTANT</b> It is mandatory to rung option A first time, so the servos are correctly aligned.
+<b>VERY IMPORTANT!!!</b> It is mandatory to rung option A first time, so the servos are correctly aligned.
@@ Line 107: / Line 107: @@
-<h1> ¡¡¡¡¡CHECK AFTER HERE!!!!! </h1>
+<h1> CHECK AFTER HERE!!!!! </h1>

← Older revision		Revision as of 18:12, 11 June 2026
Line 98:		Line 98:
	</pre>		</pre>

−	<b>It is mandatory to rung option A first time, so the servos are correctly aligned. ~~</b>~~	+	<b>VERY IMPORTANT</b> It is mandatory to rung option A first time, so the servos are correctly aligned.

← Older revision		Revision as of 18:12, 11 June 2026
Line 98:		Line 98:
	</pre>		</pre>

−	It is mandatory to rung option A first time, so the servos are correctly aligned.	+	<b>It is mandatory to rung option A first time, so the servos are correctly aligned. </b>

@@ Line 74: / Line 74: @@
 <h1> FOR CONFIGURATION ONLY </h1>
 Please download configApp from [[https://www.robolabo.etsit.upm.es/wikiFiles/PhantomReactorV2_configAPP.tgz here ]] in your prefered destination.
 <h1> ¡¡¡¡¡CHECK AFTER HERE!!!!! </h1>
-<!--
 <h1> Hello World example  </h1>
@@ Line 304: / Line 341: @@
 <br>
 Moreover, in the <i> poses.h </i> file you can find some examples of how to define the generalized coordinates of your system.

@@ Line 71: / Line 71: @@
 If you are using Windows, power up the robot and connect it to your computer.
 Windows should ask you to install some FTDI drivers to be able to connect to the robot. -->
 <h1> FOR CONFIGURATION ONLY </h1>
@@ Line 81: / Line 78: @@
 <h1> ¡¡¡¡¡CHECK AFTER HERE!!!!! </h1>
 <h1> Hello World example  </h1>
@@ Line 306: / Line 304: @@
 <br>
 Moreover, in the <i> poses.h </i> file you can find some examples of how to define the generalized coordinates of your system.

← Older revision		Revision as of 18:08, 11 June 2026
Line 72:		Line 72:
	Windows should ask you to install some FTDI drivers to be able to connect to the robot. -->		Windows should ask you to install some FTDI drivers to be able to connect to the robot. -->

		+
		+
		+
		+	<h1> FOR CONFIGURATION ONLY </h1>
		+	Please download configApp from [[https://www.robolabo.etsit.upm.es/wikiFiles/PhantomReactorV2_configAPP.tgz here ]] in your prefered destination.
		+
		+
		+
		+	<h1> ¡¡¡¡¡CHECK AFTER HERE!!!!! </h1>
	<h1> Hello World example </h1>		<h1> Hello World example </h1>

@@ Line 30: / Line 30: @@
 <li>Go to Tools > Board > Boards Manager.
-Search for Arduino SAMD and Install the latest version.
+Search for <b>Arduino SAMD</b> and Install the latest version.
 <li> Go to Tools > Board > Boards Manager.
-Search for OpenRB and Install the latest version.
+Search for <b>OpenRB</b> and Install the latest version.
 <li> Go to Sketch -> Include library -> Manage Library
-Search for DYNAMIXEL2Arduino from the Library Manager and install the library.
+Search for <b>DYNAMIXEL2Arduino</b> from the Library Manager and install the library.
 </ul>

@@ Line 1: / Line 1: @@
 __TOC__
-<b> Note: </b> Most of the information of this website is obtained from:
+<b> Note: </b> Most of the information of this website is obtained from: http://learn.trossenrobotics.com/projects/182-arbotix-getting-started-guide-arduino-ide-1-6-x-setup.html
-https://emanual.robotis.com/docs/en/parts/controller/openrb-150/#install-the-arduino-ide
 Please refer to the previuos link if you need more information.
@@ Line 22: / Line 21: @@
 <h2> Installing Tools and Libraries </h2>
 <ul>
-<li> Download the robot libraries from: [[https://www.robolabo.etsit.upm.es/wikiFiles/Arbotix-arduino-1-6.zip here ]]. </li>
+<li>
-<li> Uncompress the libraries to a path of your convenience. In this file you will find two folders: <b> hardware </b> and <b> libraries </b>
+On the Arduino IDE, go to File > Preferences from the top menu.
-<li> Copy both folders to the <ARDUINO_MAIN_DIRECTORY>. In some Windows you will find this folder in <i> My Documents\Arduino\ </i>, while in others you will find it in <i> Documents\Arduino\ </i>.
+When the Preferences window appears, copy and paste following address in the Additional Boards Manager URLs textbox.
-In Linux you will find this folder in <i>~/Arduino/</i>.<br>
 </ul>
@@ Line 34: / Line 43: @@
 <ul>
 <li> Open/run Arduino IDE </li>
-<li> Open a Robot Test: </li>
+<li> Open a Test: </li>
 <pre>
-File -> Examples -->ArbotiX --> Tests --> ReactorTest
+File -> Examples --> Dynamixel2Arduino --> basic --> ping
 </pre>
-<li> Select the Arbotix board </li>
+<li> Select the OpenRB-150 board</li>
 <pre>
-Tools -> Board -> ArbotiX Std
+Tools -> Board -> OpenRB-150 Std
 </pre>
 <li> Compile the program </li>
 <pre>
-Program-> Verify/Compile
+Sketch-> Verify/Compile
 </pre>
@@ Line 55: / Line 64: @@
 </ul>
-<h3> Installing FTDI drivers </h3>
+<!--<h3> Installing FTDI drivers </h3>
 If you are using Linux or Mac, skip this step.
 If you are using Windows, power up the robot and connect it to your computer.
-Windows should ask you to install some FTDI drivers to be able to connect to the robot.
+Windows should ask you to install some FTDI drivers to be able to connect to the robot. -->
 <h1> Hello World example  </h1>

PhantomX Reactor Robot V2 - Revision history

Aguti at 18:12, 11 June 2026

Aguti at 18:12, 11 June 2026

Aguti at 18:12, 11 June 2026

Aguti at 18:11, 11 June 2026

Aguti at 18:09, 11 June 2026

Aguti at 18:08, 11 June 2026

Aguti at 18:04, 11 June 2026

Aguti at 18:01, 11 June 2026

Aguti: Created page with "__TOC__ Note: Most of the information of this website is obtained from: https://emanual.robotis.com/docs/en/parts/controller/openrb-150/#install-the-arduino-ide Ple..."

Aguti: Created page with "TOC Note: Most of the information of this website is obtained from: https://emanual.robotis.com/docs/en/parts/controller/openrb-150/#install-the-arduino-ide Ple..."