Difference between revisions of "Nucleo Boards"

From RobolaboWiki
Jump to: navigation, search
 
(33 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
__TOC__
 
__TOC__
  
 +
<!--
 
<h1> Configuring environment </h1>
 
<h1> Configuring environment </h1>
 
<h2> Linux </h2>
 
<h2> Linux </h2>
Line 32: Line 33:
 
sudo make install
 
sudo make install
 
</pre>
 
</pre>
−
 
  
 
<h3> References </h3>
 
<h3> References </h3>
Line 39: Line 39:
 
https://nebkelectronics.wordpress.com/2017/10/08/stm32cube-library-part-3-compiling/
 
https://nebkelectronics.wordpress.com/2017/10/08/stm32cube-library-part-3-compiling/
  
−
<h2> Windows </h2>
+
 
−
<h2> MAC </h2>
+
-->
 +
 
 +
<h1> STM32CubeIDE </h1>
 +
<h2> Installation </h2>
 +
 
 +
<h3> Linux </h3>
 +
 
 +
Last release of STM32CubeIDE can be obtained here: https://www.st.com/en/development-tools/stm32cubeide.html. <br>
 +
For Debian like distributions (e.g. ubuntu), download the STM32CubeIDE-DEB file. To download it, you will need to provide name and a valid email address.
 +
 
 +
Unzip the file (e.g. <FILE> = en.st-stm32cubeide_1.0.1_3139_20190612_1256_amd64.deb_bundle)
 +
 
 +
<pre>
 +
unzip <FILE>.sh.zip
 +
</pre>
 +
 
 +
It will generate a .sh file.
 +
Give it permits for execution.
 +
 
 +
<pre>
 +
chmod 777 <FILE>.sh
 +
</pre>
 +
 
 +
Finally, execute the installation
 +
<pre>
 +
sudo ./<FILE>.sh
 +
</pre>
 +
 
 +
You must accept all license agreements.
 +
 
 +
 
 +
<h3> Windows </h3>
 +
 
 +
Last release of STM32CubeIDE can be obtained here: https://www.st.com/en/development-tools/stm32cubeide.html. <br>
 +
For Windows like distributions, download the STM32CubeIDE-Win file. To download it, you will need to provide name and a valid email address.
 +
 
 +
Unzip the file and execute the binary. Follow all steps and accept all conditions.
 +
 
 +
<h3> MAC </h3>
 +
Last release of STM32CubeIDE can be obtained here: https://www.st.com/en/development-tools/stm32cubeide.html. <br>
 +
For MAC like distributions, download the STM32CubeIDE-MAC file. To download it, you will need to provide name and a valid email address.
 +
 
 +
Unzip the file and execute the binary. Follow all steps and accept all conditions.
 +
 
 +
<b> IMPORTANT </b> Some problems have been reported related to lasts versions of STM32CubeIDE-MAC, where the code generator does not include macro definitions for the peripheral of nucleo-boards. Last version correctly tested is 1.0.0.
 +
 
 +
<h2> Hello World </h2>
 +
In this Section a Hellow World (led blinking) example will be programmed on a NUCLEO-F446RE board:
 +
 
 +
<ul>
 +
<li> Open STM32CubeIDE </li>
 +
<li> Select where to store the workspace. This will be the folder where different projects could be stored. </li>
 +
<li> Select <b> Start new STM32 project </b> </li>
 +
<li> A microcontroller or board should be selected. In our case, a NUCLEO-F446RE will be used.
 +
Then, select <b> board selector </b>  and search part number <b> Nucleo-F446RE </b>. Once chosen, press <b> Next </b> </li>
 +
<li> Chose a Project name (e.g. ledp) and keep the rest of parameters as they are. Press <b> Finish </b></li>
 +
<li> The STM32CubeIDE will ask if you want  Initialize all peripherals with their default Mode. Answer <b> Yes </b> </li>
 +
<li> The STM32CubeIDE will inform that yhis kind of projects is associated with the STM32CubeMx prespective and will ask if you want to open this perspective now. Answer <b> Yes </b>. <br>
 +
Download of required libraries will start. It could take long for the first time depending on your connection settings.  </li>
 +
<li> Once the project is open, on the left side on the "Project Explorer", look for <i> Src -> main.c </i>. <br>
 +
Inside the code, look for the <i> while(1) </i> sentence in the <i> main(void) </i> function, and fill it as follows:
 +
<pre>
 +
while (1)
 +
{
 +
  HAL_GPIO_TogglePin(LD2_GPIO_Port, LD2_Pin);
 +
  HAL_Delay(100);
 +
/* USER CODE END WHILE */
 +
 
 +
/* USER CODE BEGIN 3 */
 +
}
 +
/* USER CODE END 3 */
 +
 
 +
</pre> </li>
 +
 
 +
<li> In order to compile, Go to <i> Project -> Build All (Ctrl+B or Hammer) </i>. It should compile the code without errors. <br>
 +
If any error appears, previous steps should be reviewed. </li>
 +
<li> In order to start the debugger, Go to <i> Run -> Debug (F11 or bug) </i> <br>
 +
Select STM32 MCU C/C++ Application and Press <b> OK </b> </li>
 +
<li> Leave all configuration propeties as they are and Press <b> OK </b> </li>
 +
<li> The STM32CubeIDE will ask if you want to switch to the debug perspective say <b> Switch </b> </li>
 +
<li> In order to execute the code, Go to <i> Run -> Resume (F8 or Green Arrow) </i>. <br>
 +
The led should be blinking at 100 ms. </li>
 +
 
 +
</ul>
 +
 
 +
<h2> Problems with STM32CUBEIDE </h2>
 +
<h3> sprintf %f </h3>
 +
 
 +
All the information on this page is obtained from: http://www.nadler.com/embedded/newlibAndFreeRTOS.html
 +
There is some errors on the implementation of malloc on STM32CubeMX, so if using some newlib fuctions (e.g. sprintf %f), the following steps must be implemented:
 +
 
 +
<ul>
 +
<li> Remove heapX.c form Middlewares->Thirs_Party->FreeRTOS->Source->CMSIS_RTOS_V2->portable->MemMang->heap_X.c </li>
 +
<li> Add this file to the Src directory: [[media:heap_useNewlib.txt | heap_useNewlib]] and rename it as heap_useNewlib.c</li>
 +
<li> Comment _sbrk function on sysmem.c file; it is already implemented on heap_useNewlib.c </li>
 +
<li> Include in FreeRTOSConfig.h the folowing directive: </li>
 +
<pre>
 +
#define configUSE_NEWLIB_REENTRANT 1
 +
</pre>
 +
<li> Go to Project -> Porperties -> MCU Settings -> Tool Settings and select float for printf and scanf from newlib-nano </li>
 +
</ul>
 +
 
 +
<h3> IDE Flickering </h3>
 +
 
 +
First check the value of GTK_IM_MODULE in your environment by executing
 +
 
 +
<pre>
 +
echo $GTK_IM_MODULE
 +
</pre>
 +
 
 +
If the output is "xim", Eclipse expects it to be “ibus”.
 +
So enter the following command in a terminal session to set it to the value.
 +
 
 +
<pre>
 +
export GTK_IM_MODULE="ibus"
 +
</pre>
 +
 
 +
Now if you launch Eclipse from the same terminal session, you should not experience any flickering issue.
 +
If you launch eclipse from a desktop menu entry, then edit the .desktop file (e.g.  /usr/share/applications/st-stm32cubeide-1.6.1.desktop) and put the following string in the beginning of the Exec command:
 +
 
 +
<pre>
 +
env GTK_IM_MODULE=ibus
 +
</pre>
 +
 
 +
E.g. Exec=env GTK_IM_MODULE=ibus /opt/st/stm32cubeide_1.6.1/stm32cubeide %F

Latest revision as of 10:41, 8 February 2023


STM32CubeIDE

Installation

Linux

Last release of STM32CubeIDE can be obtained here: https://www.st.com/en/development-tools/stm32cubeide.html.
For Debian like distributions (e.g. ubuntu), download the STM32CubeIDE-DEB file. To download it, you will need to provide name and a valid email address.

Unzip the file (e.g. <FILE> = en.st-stm32cubeide_1.0.1_3139_20190612_1256_amd64.deb_bundle) 

unzip <FILE>.sh.zip

It will generate a .sh file. Give it permits for execution. 

chmod 777 <FILE>.sh

Finally, execute the installation 

sudo ./<FILE>.sh

You must accept all license agreements.


Windows

Last release of STM32CubeIDE can be obtained here: https://www.st.com/en/development-tools/stm32cubeide.html.
For Windows like distributions, download the STM32CubeIDE-Win file. To download it, you will need to provide name and a valid email address.

Unzip the file and execute the binary. Follow all steps and accept all conditions.

MAC

Last release of STM32CubeIDE can be obtained here: https://www.st.com/en/development-tools/stm32cubeide.html.
For MAC like distributions, download the STM32CubeIDE-MAC file. To download it, you will need to provide name and a valid email address.

Unzip the file and execute the binary. Follow all steps and accept all conditions.

IMPORTANT Some problems have been reported related to lasts versions of STM32CubeIDE-MAC, where the code generator does not include macro definitions for the peripheral of nucleo-boards. Last version correctly tested is 1.0.0.

Hello World

In this Section a Hellow World (led blinking) example will be programmed on a NUCLEO-F446RE board:

  • Open STM32CubeIDE
  • Select where to store the workspace. This will be the folder where different projects could be stored.
  • Select Start new STM32 project
  • A microcontroller or board should be selected. In our case, a NUCLEO-F446RE will be used. Then, select board selector and search part number Nucleo-F446RE . Once chosen, press Next
  • Chose a Project name (e.g. ledp) and keep the rest of parameters as they are. Press Finish
  • The STM32CubeIDE will ask if you want Initialize all peripherals with their default Mode. Answer Yes
  • The STM32CubeIDE will inform that yhis kind of projects is associated with the STM32CubeMx prespective and will ask if you want to open this perspective now. Answer Yes .
    Download of required libraries will start. It could take long for the first time depending on your connection settings.
  • Once the project is open, on the left side on the "Project Explorer", look for Src -> main.c .
    Inside the code, look for the while(1) sentence in the main(void) function, and fill it as follows: 
    while (1)
{
  HAL_GPIO_TogglePin(LD2_GPIO_Port, LD2_Pin);
  HAL_Delay(100);
 /* USER CODE END WHILE */

 /* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
  • In order to compile, Go to Project -> Build All (Ctrl+B or Hammer) . It should compile the code without errors.
    If any error appears, previous steps should be reviewed.
  • In order to start the debugger, Go to Run -> Debug (F11 or bug)
    Select STM32 MCU C/C++ Application and Press OK
  • Leave all configuration propeties as they are and Press OK
  • The STM32CubeIDE will ask if you want to switch to the debug perspective say Switch
  • In order to execute the code, Go to Run -> Resume (F8 or Green Arrow) .
    The led should be blinking at 100 ms.

Problems with STM32CUBEIDE

sprintf %f

All the information on this page is obtained from: http://www.nadler.com/embedded/newlibAndFreeRTOS.html There is some errors on the implementation of malloc on STM32CubeMX, so if using some newlib fuctions (e.g. sprintf %f), the following steps must be implemented:

  • Remove heapX.c form Middlewares->Thirs_Party->FreeRTOS->Source->CMSIS_RTOS_V2->portable->MemMang->heap_X.c
  • Add this file to the Src directory: heap_useNewlib and rename it as heap_useNewlib.c
  • Comment _sbrk function on sysmem.c file; it is already implemented on heap_useNewlib.c
  • Include in FreeRTOSConfig.h the folowing directive: 
    • #define configUSE_NEWLIB_REENTRANT 1
  • Go to Project -> Porperties -> MCU Settings -> Tool Settings and select float for printf and scanf from newlib-nano

IDE Flickering

First check the value of GTK_IM_MODULE in your environment by executing 

echo $GTK_IM_MODULE

If the output is "xim", Eclipse expects it to be “ibus”. So enter the following command in a terminal session to set it to the value. 

export GTK_IM_MODULE="ibus"

Now if you launch Eclipse from the same terminal session, you should not experience any flickering issue. If you launch eclipse from a desktop menu entry, then edit the .desktop file (e.g. /usr/share/applications/st-stm32cubeide-1.6.1.desktop) and put the following string in the beginning of the Exec command: 

env GTK_IM_MODULE=ibus

E.g. Exec=env GTK_IM_MODULE=ibus /opt/st/stm32cubeide_1.6.1/stm32cubeide %F

Retrieved from "http://wiki.robolabo.etsit.upm.es/index.php?title=Nucleo_Boards&oldid=2036"