View source for PhantomX Reactor Robot

__TOC__

<b> Note: </b> Most of the information of this website is obtained from: http://learn.trossenrobotics.com/projects/182-arbotix-getting-started-guide-arduino-ide-1-6-x-setup.html
Please refer to the previuos link if you need more information.

<h1> Configuring the environment  </h1>

<h2> Setting up the Arduino Software </h2>

<ul>
<li> Download the Arduino IDE 1.6.x according to your operating system from: https://www.arduino.cc/en/Main/Software . </li>
<li> Install the Arduino IDE </li>
<ul>
<li> If you have chosen to download the installer, run the installer and install the software in a path of your convenience. </li>
<li> If you have chosen to download the sources (Linux or zip on Windows), uncompress the software in a path of your convenience </li>
</ul>
<li> Open/run Arduino IDE, so it will create all the folders needed</li>
<li> Close Arduino IDE </li>
</ul>

<h2> Installing Tools and Libraries </h2>
<ul>
<li> Download the robot libraries from: [[media:arbotix-arduino-1-6.zip | here ]]. </li>
<li> Uncompress the libraries to a path of your convenience. In this file you will find two folders: <b> hardware </b> and <b> libraries </b>
<li> Copy both folders to the <ARDUINO_MAIN_DIRECTORY>. In some Windows you will find this folder in <i> My Documents\Arduino\ </i>, while in others you will find it in <i> Documents\Arduino\ </i>.
In Linux you will find this folder in <i>~/Arduino/</i>.<br>

<b> Important: </b> If you already have a <i>libraries</i> folder inside your <ARDUINO_MAIN_DIRECTORY>, move the content of the <i>libraries</i> folder downloaded inside the <i>libraries</i> folder of <ARDUINO_MAIN_DIRECTORY>.
</ul>

<h2> Check installation </h2>
<ul>
<li> Open/run Arduino IDE </li>
<li> Open a Robot Test: </li>

<pre> 
File -> Examples -->ArbotiX --> Tests --> ReactorTest
</pre>

<li> Select the Arbotix board </li>
<pre>
Tools -> Board -> ArbotiX Std
</pre>

<li> Compile the program </li>
<pre>
Program-> Verify/Compile
</pre>

If there is no errors, you are ready for the next step.
If you found some errors, please review the previous steps.

<li> Close Arduino IDE
</ul>

<h3> Installing FTDI drivers </h3>
If you are using Linux or Mac, skip this step.
If you are using Windows, power up the robot and connect it to your computer.
Windows should ask you to install some FTDI drivers to be able to connect to the robot.

<h1> Hello World example  </h1>

We have created a helloWorld example to test the communication with the robot.
Please download it from [[media:ROB-HelloWorldPhantomReactor.tgz | here ]] in your prefered destination.
Untar the file:
<pre>
tar -xvzf helloWorld.tgz
</pre>

<h2> Compiling the code </h2>
<li> Open Arduino IDE and load the .ino file in your environment: </li>
<pre>
File --> Open --> <HELLOWORLD_EXAMPLE>
</pre>

<li> Select the Arbotix board: </li>
<pre>
Tools -> Board -> ArbotiX Std
</pre>

<li> Compile the program: </li>
<pre>
Program-> Verify/Compile
</pre>

<h2> Downloading the code to the robot </h2>
Once compiled, select the correct por to download the binaries:
In Linux, typically:
<pre>
tools -> Port -> /dev/ttyUSBX
</pre>

In Windows, typically:
<pre>
tools -> Port -> COMX
</pre>

where X depends on your system and the number of peripherals on it

Upload your code to the board:
<pre>
Program -> Upload
</pre>

The IDE will notify that it is <i> uploading </i> and after some seconds it will say <i> uploaded </i>.

<h2> Playing with HelloWorld </h2>

This example allows you to move different joints of the robot.

Once the code have been loaded, you can open the serial port:
<pre>
Tools --> Serial Monitor
</pre>

In some seconds you should see the board communicating the following menu:
<pre>

################################
Serial Communication Established
################################
################################
Please enter option 1-6
0) Relax Servos
1) Hold Servos
2) Get Joints Pos
3) Gripper Close
4) Gripper Open
5) TestAllJoints
6) MoveSpecificJoint
################################
</pre>

Lets explain the different options
<ul>
<li> <b> Option 0 </b> unpowers the servomotors of the robot.
<li> <b> Option 1 </b> powers the servomotors of the robot.
<li> <b> Option 2 </b> prints the position of every generalized coordinate (Base, Shoulder, Elbow, Wrist and Wrist rotation).
<li> <b> Option 3 </b> closes the gripper.
<li> <b> Option 4 </b> opens the gripper.
<li> <b> Option 5 </b> provides a test movement for the complete robot.
<li> <b> Option 6 </b> allows to move specific joints. In this case, once the option is selected, the following menu will appear:
</ul>
<pre>
Base: 0
Shoulder: 1
Elbow: 2
Wrist: 3
Wrist Rot: 4

Joint to move?: 
</pre>

The user must choose one of the 5 options, which correspond to different joints.

For every joint, once selected, the program will ask for a position to move, given the limits of the joint, for example:

<pre>
Joint selected: 1
Shoulder: [-0.33, 2.97]
Position to move?: 
</pre>

Once the position is provided through the serial port it will return all the information inserted, for example:

<pre>
Moving Joint: 1 to position: 1.57
</pre>

and it will move to the specified position.

<h1> Practice 1 Template (P1)</h1>

For the implementation of Practice 1 of the "Control and Robotics in Medicine" subject of the "Master on Bioengineering"  of the UPM, we have created a students template.
You can download the template from [[media:ROB-P1Template.tgz | here ]]

<h2> Structure </h2> 
The template has 4 different files:
<ul>
<li> <b> poses.h </b>: A file where different generalized coordinates can be stored.
<li> <b> servos.h </b>: A library to manage the servomotors independently.
<li> <b> robot.h </b>: A library to manage the different joints of the robot.
<li> <b> P1-Template.h </b>: The place where the practice should be developped.
</ul>

<h2> Libraries </h2>
This Section provides important information for the resolution of Practice1.
It is based on the explanation of different methods to control the robot, but it does not explain the complete set of methods.
To get and exahustive description of all methods the <i> servos.h </i> and <i> robot.h </i> files must be studied.

In principle, all interaction with the robot will be made by means of the <i> robot.h </i> library.
Main methors are as follows:

<ul>
<li> <b> void ROBOT_GripperOpen(void) </b>: It opens the gripper, so it can release an object if already grasped.
<li> <b> void ROBOT_GripperClose(void) </b>: It close the gripper, so it can grasp an object if correctly located.
<li> <b> void ROBOT_SetSingleTrajectory ( double *f_pos, uint16_t un_time, uint8_t un_trajectory_type ) </b>: It performs a trajectory form one point (Q(t<sub>0</sub>)) to another point (Q(t<sub>f</sub>)).
Q(t<sub>0</sub>) and Q(t<sub>f</sub>) are defined as generalized coordinates Q={q<sub>1</sub>,q<sub>2</sub>,q<sub>3</sub>,q<sub>4</sub>,q<sub>5</sub>}.
Moreover, Q(t<sub>0</sub>) is defined as the coordinates at which the robot is located once the instruction is set.

<ul>
<li> <b>double *f_pos </b>: 
Q(t<sub>f</sub>) is coded as <i> double * </i>, for example:
<pre>
double m_fCoordTest[]       = {0,M_PI/2,-M_PI/2,0,0};
</pre>

<li> <b> uint16_t un_time </b>,  represents the time that it takes to travel from  (Q(t<sub>0</sub>)) to Q(t<sub>f</sub>),that is: t<sub>f</sub> - t<sub>0</sub> in milliseconds.

<li> <b> uint8_t un_trajectory_type </b>, represents the type of trajectory to perform: Linear (LINEAR = 0)  or Cubic  (CUBIC1 = 0)

<br>
<br>
Therefore, if we want to move the robot for the actual position to position <i> m_fCoordTest </i> taking 2 seconds with a linear function, we need to execute:

<pre>
ROBOT_SetSingleTrajectory (m_fCoordTest, 2000, LINEAR);
</pre>

I we want to move the robot to the same coordinates but in 10 secons with a cubic function, we need to execute:
<pre>
ROBOT_SetSingleTrajectory (m_fCoordTest, 10000, CUBIC1);
</pre>

<li> <b> void ROBOT_SetDoubleTrajectory ( double *un_pos1, double *un_pos2, uint16_t un_time1, uint16_t un_time2, uint8_t un_trajectory_type ) </b>: 
It performs a trajectory form one point (Q(t<sub>0</sub>)) to another point (Q(t<sub>f</sub>)) passing by a point (Q(t<sub>v</sub>)).

Q(t<sub>0</sub>), Q(t<sub>f</sub>) and Q(t<sub>v</sub>) are defined as generalized coordinates Q={q<sub>1</sub>,q<sub>2</sub>,q<sub>3</sub>,q<sub>4</sub>,q<sub>5</sub>}.
Moreover, Q(t<sub>0</sub>) is defined as the coordinates at which the robot is located once the instruction is set.

<ul>
<li> <b>double *f_pos1 </b>: 
Q(t<sub>v</sub>) is coded as <i> double * </i> , for example:
<pre>
double m_fCoordTest[]       = {0,M_PI/2,-M_PI/2,0,0};
</pre>

<li> <b>double *f_pos2 </b>: 
Q(t<sub>v</sub>) is coded as <i> double * </i>.

<li> <b> uint16_t un_time1 </b>,  represents the time that it takes to travel from  (Q(t<sub>0</sub>)) to Q(t<sub>v</sub>),that is: t<sub>v</sub> - t<sub>0</sub> in milliseconds.
<li> <b> uint16_t un_time2 </b>,  represents the time that it takes to travel from  (Q(t<sub>v</sub>)) to Q(t<sub>f</sub>),that is: t<sub>f</sub> - t<sub>v</sub> in milliseconds.

<li> <b> uint8_t un_trajectory_type </b>, represents the type of trajectory to perform. Only cubic trajectories are allowed  (CUBIC2 = 2)

<br>
<br>
Therefore, if we want to move the robot for the actual position to position <i> m_fCoordTest </i>  taking 5 seconds passing by <i> m_fCoordVia </i> with 2 seconds from the start, we need to execute:

<pre>
ROBOT_SetDoubleTrajectory (m_fCoordVia, m_fCoordTest, 2000, 3000, CUBIC2);
</pre>

</ul>